Return to Robo-Pong 2000 Parts Listing
This list to be used if you have a Model 1929 Newgy Table Tennis Robot and you are looking for a Robo-Pong 2000 part that will substitute for it.
| 1929 Part # | 1929 Part Name | 2000 Part # | 2000 Part Name | Notes |
| 752-201 | Center Trough Assembly | mismatch | different shape, color | |
| 752-202 | Metal Net Support | mismatch | not used | |
| 752-204 | Center U Support Upright | mismatch | diff. size | |
| 752-205 | Back Support Plate | mismatch | not used | |
| 752-206 | Net Support Tube Curved | mismatch | diff. length, curve | |
| 752-207 | Support Leg, L | mismatch | diff. size, curve, can use 2000-110 if it is bent slightly so robot sits level on table | |
| 752-208 | Front Support Plate | mismatch | diff. attachment | |
| 752-209 | Net Support Plate, Front | mismatch | diff. shape, size, color | |
| 752-210 | Net Support Plate, Rear | mismatch | diff. shape, size, color | |
| 752-212 | Support Leg, R | mismatch | diff. size, curve, can use 2000-112 if it is bent slightly so robot sits level on table | |
| 752-213 | Net Support Tube, Strght | mismatch | diff. length | |
| 752-217 | Net | mismatch | diff. shape, size | |
| 752-219 | 1/4×3/4 Phillips Head Screw | mismatch | not used | |
| 752-225 | #8×1" Machine Screws | mismatch | diff. thread, can use 2000-302 if replaced along with 2000-310 | |
| 752-227 | #8-32 Hex Nut | mismatch | diff. thread, can use 2000-310 if replaced along with 2000-302 | |
| 752-228 | Large Flat Washer | mismatch | not used | |
| 752-229 | Rubber Crutch Tip | 2000-118 | CT Support Leg Tip, 1" | same |
| 752-230 | 1/4-20 Wing Nut | mismatch | different size, thread | |
| 752-232 | 1/4-20 Hex Nut | mismatch | not used | |
| 752-236 | 1/4-20 x 1" Hex Bolt | mismatch | not used | |
| 752-302 | Ball Return Tray, L | mismatch | different shape, size, color | |
| 752-303 | Ball Return Tray, R | mismatch | different shape, size, color | |
| 752-304 | Tray Strap | 2000-140 | Tray Strap | same |
| 753-101 | Back Panel | mismatch | diff. color, support wings finished on opposite side, can use 2000-142 if you round off top tab & widen opening in bottom of support flange and you replace it along with 2000-146, 2000-156, 2000-154, & 2000-318 | |
| 753-101N | New Back Panel | mismatch | diff. color, support wings finished on opposite side, can use 2000-142 if you round off top tab and widen opening in bottom of support flange | |
| 753-102 | Front Panel | 2000-162 | Front Cover | diff. color, shape, could be used for 2000-162 if necessary, but may interfere with ball channeling |
| 753-103 | Ball Return Plate | 2000-144 | Ball Feed Collector Plate | diff. color, not normally seen (covered by balls) |
| 753-104 | Ball Return Housing | mismatch | diff. shape, color, attachment | |
| 753-105 | Ball Return Adapter | 2000-196 | Oscillator Pivot Guide | different color |
| 753-106 | Pan. Gears & Motor Hsng. | 2000-204 | Oscillator Motor Cover | different color |
| 753-107 | Ball Discharge Tube | 2000-166 | Ball Feed Discharge Tube | different color, not easily seen |
| 753-108 | Ball Discharge Housing, L | 2000-172 | Robot Head Housing, L. | different color |
| 753-109 | Ball Discharge Housing, R | 2000-174 | Robot Head Housing, R. | different color |
| 753-110 | Pan. Motor & Gear Frame | 2000-206 | Osc. Motor Mounting Plate | diff. color, not visible on outside, if replacing 753-110 with 2000-206, use only 2000-326 screws |
| 753-111 | Ball Return Motor & Gear Housing | mismatch | not used, can use 2000-146 if replaced along with 2000-156, 2000-154, 2000-318, & 2000-142. | |
| 753-111A | Ball Feed Back Plate | 2000-146 | BF Gear Mounting Plate | diff. color, not easily seen |
| 753-111B | New Ball Feed Motor Frame | 2000-156 | BF Motor Mount Housing | diff. color, not easily seen |
| 753-111C | Ball Feed Brass Gear Posts | 2000-154 | BF Transfer Gear Brass Shaft | same |
| 753-111D | Screws For 753-111A | 2000-318 | BF #4×5/16 Machine Screw | same |
| 753-112 | Control Lever Adapter | mismatch | diff. shape, color, can use 2000-198 if replaced along with 2000-200 & 2000-202 | |
| 753-112N | New Control Lever Adapter | 2000-198 | Osc.Control Lever Adapter | diff. color, includes lever guard |
| 753-113 | Friction Block | mismatch | diff. color (not easily seen), tabs are shorter, can use 2000-192 if replaced along with 2000-190, 2000-184, & 2000-324 | |
| 753-113N | New Friction Block | 2000-192 | Ball Feed Friction Block | diff. color, not easily seen |
| 753-114 | Old Ball Discharge Wheel | mismatch | not used, has small undulations in wheel surface, can use 2000-190 if replaced along with 2000-192, 2000-184, and 2000-324 | |
| 753-114N | New Ball Discharge Wheel | 2000-190 | Ball Speed Discharge Wheel | diff. color, not easily seen |
| 753-115 | Motor Cap-Ball Discharge | 2000-188 | Ball Speed Motor Cover | diff. color |
| 753-116 | Ball Return Gear | 2000-148 | Ball Feed Main Gear | diff. color, not normally seen (covered by balls) |
| 753-117 | Osc. Motor & Pinion Gear | 2000-148 | Osc. Motor W/Brass Gear | same |
| 753-117W | Oscillator Wire | 2000-210 | Osc. Power Wire | same |
| 753-118 | Control Lever, R | mismatch | diff color, shape, can use 2000-202 if replaced along with 2000-198 & 2000-200 | |
| 753-118N | New Control Lever, R | 2000-202 | Control Lever, R | diff. color |
| 753-119 | Control Lever, L | mismatch | diff color, shape, can use 2000-200 if replaced along with 2000-198 & 2000-202 | |
| 753-119N | New Control Lever, L | 2000-200 | Control Lever, L | diff. color |
| 753-120 | Ball Discharge Knob Nut | same as 753-227 | ||
| 753-121 | Ball Discharge Tube Pivot Screw | same as 753-143 | ||
| 753-123 | Ball Gear Fingers | 2000-150 | BF Main Gear Fingers | diff color, not normally seen (covered by balls) |
| 753-124 | Motor Bracket | 2000-212 | Osc.Motor Mount Bracket | same |
| 753-125 | Gear & Pinion Cluster | 2000-152 | BF White Transfer Gear | same |
| 753-126 | Panning Drive Gear | 2000-216 | Osc. White Drive Gear | same |
| 753-128 | Brake-Ball Discharge Tube | 2000-168 | BF Discharge Tube Brake | same |
| 753-129 | Horizontal Pointer | 2000-182 | Robot Head Angle Pointer | same |
| 753-138 | Ball Discharge Adjusting Knob | mismatch | diff. thread, can use 2000-180 if replaced along with 2000-322 | |
| 753-139 | Ball Discharge Comp. Spring | 2000-178 | RH Steel Ball Spring | same |
| 753-140 | Friction Block Spring | 2000-194 | BS Friction Block Spring | same |
| 753-141 | Ball Sp. Motor & Pinion Gear | mismatch | diff. size drive shaft, has right hand threads in shaft, can use 2000-184 if replaced along with 2000-192, 2000-190, and 2000-324 | |
| 753-141N | New Ball Speed Motor | 2000-184 | BS Motor W/Brass Shaft | same (has left hand threads in shaft) |
| 753-141W | Ball Speed Coiled Cord | 2000-186 | BS Coiled Power Wire | same |
| 753-142 | Oscillator Gear Washer | mismatch | not used (2000-326 has washer-type head) | |
| 753-143 | #4×3/8 Self Tap Screw, Bl. | 2000-328 | #4×3/8 Self Tap Screw | same |
| 753-144 | #4×3/8 Self Tap Screw, Gld | mismatch | not used, can be substituted for 2000-328 | |
| 753-145 | Ball Discharge Wheel Screw | mismatch | right hand threads, can use 2000-324 if replaced along with 2000-192, 2000-190, and 2000-184 | |
| 753-145N | Ball Discharge Wheel Screw, (L Thread) |
2000-324 | BS Discharge Wheel Screw | same, left hand threads |
| 753-146 | Ball Disc. Whl. Lock Washer | mismatch | not used | |
| 753-147 | #1×3/16 Thread Form. Screw | mismatch | diff. thread, use 753-147 only with 753-110 that has solid plastic posts, do not use if 753-110 has brass posts (use 2000-326 instead) | |
| 753-148 | Ball Feed Motor & Gear | 2000-158 | BF Motor W/Brass Gear | same |
| 753-148W | Ball Feed Wire | 2000-160 | BF Power Wire | same |
| 753-149 | #8 x 5/16 Self Tap. Screw | mismatch | not used | |
| 753-150 | Ball Discharge Spring | 2000-170 | Ball Feed Discharge Spring | same |
| 753-151 | 5 Pin Receptacle | 2000-218 | 5 Pin Connector | same |
| 753-152 | Connector Cable | 2000-220 | Connector Cable | end terminals not removable |
| 753-153 | Ball Feed Gear Washer | 2000-314 | Large Washer | same |
| 753-154 | Steel Ball | 2000-176 | Robot Head Steel Ball | same |
| 753-155 | Ball Disc. Housing Screw | 2000-320 | RH #8×1 3/16 Machine Scw | same |
| 753-156 | 3/16 Motor Mount Screw | 2000-330 | #2×1/4 Machine Screw | has washer type head, washer not necessary |
| 753-232 | 3/4 Shoulder Bolt For Trays | mismatch | not used | |
| 753-232A | 3/8 Lock Nut For Trays | mismatch | not used | |
| 753-350 | Control Box | 2000-224 | Control Box | different electronics, labels, has Pong-Master connection |
| 753-350-1 | Voltage Regulator (Q1&Q3) | 2000-224-8 | Osc. & Ball Speed Voltage Regulator | same |
| 753-350-2 | Voltage Regulator (Q2) | 2000-224-7 | Ball Frequency Voltage Regulator | same |
| 753-350-5 | Small Capacitor (C1–C4) | ? | ? | |
| 753-350-6 | Large Capacitor (C5) | mismatch | both leads at one end | |
| 753-350-7 | Resistor (R1 & R3) | ? | ? | |
| 753-350-8 | Resistor (R2) | ? | ? | |
| 753-350-9 | Ball Speed Potentiometer | mismatch | longer leads with different shape | |
| 753-350-10 | Ball Freq. Potentiometer | mismatch | longer leads with different shape, diff range | |
| 753-350-11 | Osc. Speed Potentiometer | mismatch | longer leads with different shape | |
| 753-350-15 | Power Jack | 2000-224-6 | Power Jack | same |
| 753-350-16 | Lighted Power Switch | 2000-224-17 | Lighted Power Switch | same |
| 753-350-25 | Foam Pad For Control Box | 2000-224-18 | Control Box Foam Pad | same |
| 753-350-26 | Control Box Knobs | 2000-224-12 | Control Box Knob | same |
| 753-450 | Transformer | 2000-222 | Transformer Cord | same |
| 900-125 | Owner’s Manual | mismatch | not the same | |
| 900-130 | Ball Dams (Pair) | mismatch | diff. shape, size, color | |
| 900-134 | End Fitting For Conn Cable | mismatch | not used |
Authored by Jie Sang . Updated 8/4/98.
Copyright © 1997 Newgy Industries. All rights reserved.
Information in this document is subject to change without notice.
Other products and companies referred to herein are trademarks or registered trademarks of
their respective companies or mark holders.